How to Seal Concrete Crafts (Indoor and Outdoor Sealers)

1. 1

   Step 1: Cure and Clean the Piece First

   Watch this step · 4:10

   Enlarge

   Before any sealer touches your concrete, make sure the piece is fully cured. Fresh concrete looks dry on the surface long before it has hardened all the way through, so give it at least 24 to 48 hours, and longer for thicker pieces. Seal too early and you trap moisture inside, so the coat will not bond.

   Once it is cured, wipe it down. Run a dry cloth or a soft brush over the surface to clear off dust and loose grit. Any powder left behind gets locked under the sealer and shows up as a rough patch, so a quick clean now pays off later.

   Tip:

   Watch this step If the concrete still feels cool or damp to the touch, it needs more time. A fully cured piece feels dry and sits at room temperature.

   Mark step done

   Used in this steplint-free microfiber clothtack cloth

   Back to all steps

2. 2

   Step 2: Choose Your Sealer, Indoor or Outdoor

   Watch this step · 3:48

   Enlarge

   This is the decision that matters most. For indoor pieces, a water-based acrylic sealer is the friendly pick: low odor, quick drying, and it wipes on clean. If the piece will hold a candle, food, or water, step up to a food-safe sealer rated for that use. Bree uses a non-toxic, water-based sealer on her candle jars for exactly that reason.

   For anything living outdoors, reach for a penetrating outdoor sealer. It sinks into the concrete instead of sitting on top, so it handles sun, rain, and freeze-thaw without peeling. Match the sealer to the job and the finish holds up.

   Tip:

   Watch this step Want a matte look on the outside? A matte varnish keeps that raw concrete feel while still adding protection. Satin and gloss are there if you want more shine.

   Mark step done

   Used in this stepwater-based acrylic concrete sealerfood-safe concrete sealerpenetrating outdoor concrete sealermatte concrete varnish

   Back to all steps

3. 3

   Step 3: Load Your Foam Brush

   Watch this step · 4:32

   Enlarge

   A foam brush is the tool for this. It lays sealer down smooth with no bristle marks, and it costs little enough to toss when you are done. Dip it into the sealer and coat both flat sides evenly.

   A little goes a long way, so press the brush against the rim of the jar to squeeze off the extra. You want the foam damp, not dripping. Too much sealer at once pools in corners and dries cloudy, so build it up in thin passes instead.

   Tip:

   Watch this step Keep a second foam brush within reach. If the first one starts to crumble or stiffen up, swap it out rather than fighting a falling-apart tip.

   Mark step done

   Used in this stepfoam sponge brushesdisposable nitrile gloves

   Back to all steps
4. 4

   Step 4: Brush On the First Coat

   Watch this step · 4:48

   Enlarge

   Start your first coat in straight vertical strokes and work your way around the whole piece. On the inside of a vessel, run the brush from the base up to the rim, turning the piece as you go so you cover every section.

   Here is the handy part: the sealer darkens the concrete a little where it lands. That wet line shows you exactly what you have covered and what you still need to reach, so you are far less likely to miss a spot. Keep the coat thin and even.

   Tip:

   Watch this step Work over a sheet of scrap paper. Drips wipe off a cured surface easily, but there is no reason to make extra cleanup for yourself.

   Mark step done

   Used in this stepwater-based acrylic concrete sealerfoam sponge brushes

   Back to all steps

5. 5

   Step 5: Add a Second Coat in the Other Direction

   Watch this step · 5:40

   Enlarge

   Let the first coat dry. Bree finds hers is ready in about half an hour to an hour, though a thick coat or a humid day takes longer. When it no longer looks or feels tacky, go back in with a second coat.

   Run this one in horizontal strokes, crossing the direction you used the first time. That cross-hatch catches any thin spots and evens out the coverage. Two coats is the standard for most pieces. Add a third if you want extra protection on something that will get heavy use.

   Tip:

   Watch this step Do not rush the dry time between coats. A second coat over a tacky first coat lifts and streaks instead of building up cleanly.

   Mark step done

   Used in this stepwater-based acrylic concrete sealerfoam sponge brushes

   Back to all steps

6. 6

   Step 6: Seal the Bottom and Base Edge

   Watch this step · 5:45

   Enlarge

   The bottom is the part people forget, and it is the part that sits on your furniture. Load a little sealer on the corner of the brush and swirl it across the base until the whole underside is coated. Get the bottom edge where the wall meets the base while you are there.

   Sealing here does two jobs. It stops raw concrete from scratching or leaving gray marks on a table, and it blocks moisture from wicking up through the base. A sealed bottom is what makes a piece safe to set down anywhere.

   Tip:

   Watch this step Set the piece on a few painters pyramids to dry so the fresh sealer on the base does not stick to your work surface.

   Mark step done

   Used in this stepwater-based acrylic concrete sealerpainters pyramid stands

   Back to all steps

7. 7

   Step 7: Cure, Then Finish and Care for It

   Watch this step · 6:00

   Enlarge

   Give the sealed piece a full 24 hours to cure before you use it or add anything to it. Bree waits at least that long before pouring wax into her jars, and the same patience pays off for a planter or a dish. Rushing it now undoes the work you just did.

   Once it is cured you can leave the finish as is, or buff on a thin coat of clear wax for a soft sheen and a little extra water resistance. To keep a sealed piece looking good, wipe it with a damp cloth and skip harsh scrubbers, which wear the sealer down over time.

   Tip:

   Watch this step Reseal every year or two on pieces that get daily use or live outside. A quick single coat brings the protection right back.

   Mark step done

   Used in this stepclear finishing waxmicrofiber buffing cloth

   Back to all steps

Keep going

How to Make a Concrete Pumpkin (Fall Decor)

→

Tools we recommend

• E6000

  E6000 Craft Adhesive, Clear (3.7 oz)

  The industrial-strength craft glue that bonds glass, wood, ceramic, metal, fabric, and concrete. The one adhesive most craft projects reach for.

• Gorilla

  Gorilla Dual-Temp Full-Size Hot Glue Gun

  Dual-temp so it handles delicate florals and heavy materials alike. A precise nozzle and built-in stand make it the everyday craft-table gun.

• OLFA

  OLFA 18" x 24" Self-Healing Cutting Mat

  The pro-standard cutting surface. Gridlines for square cuts, self-healing so blades never leave grooves, and big enough for paper, fabric, and leather.

Tags