How to Make a Letter Bead Friendship Bracelet

1. 1

   Step 1: Pick your word and pull your alphabet beads

   Watch this step · 1:50

   Enlarge

   Decide what you want the bracelet to say. A name, a one-word reminder, a song lyric, a phone number - anything that fits across the front of your wrist. Short words read best. "MAMA", "LOVE", "OLIVIA", "CHOOSE JOY" - all good lengths.

   Then dig out the letters from your alphabet bead mix. You'll need two options for letter beads: round flat ones (7mm by 3.5mm, letters on two sides) or cube ones (6mm, letters on all four sides). Both work. Cubes are louder and easier to read; rounds lie flatter.

   Tip:

   Round flat beads sit nicer side by side on a long word. Cubes need a seed bead between each letter or they start to look chunky on the curve.

   Mark step done

   Used in this stepAlphabet Bead Variety PackBead Design Board

   Back to all steps

2. 2

   Step 2: Frame the word with seed beads

   Watch this step · 2:45

   Enlarge

   Set a 4mm seed bead on each side of the word. The frame makes the letters pop against the band beads and gives you something neutral to slide over the knot at the back later.

   If your word has two parts - say a first and middle name, or two short words - drop a single contrasting bead in the gap. A black faceted bead between "CHOOSE" and "JOY" reads as a tiny visual pause without leaving an awkward space.

   Mark step done

   Used in this step4mm Seed Beads

   Back to all steps

3. 3

   Step 3: Measure your wrist and set the length

   Watch this step · 3:20

   Enlarge

   Wrap a tape measure around your wrist where the bracelet will sit. Add 2.5 to 3 centimeters (about an inch) for stretch. A 16.5cm wrist becomes a 19cm beaded bracelet.

   That extra centimeter or so is what lets the bracelet slide on without straining the elastic. Too tight and the cord fatigues fast. Too loose and the bracelet flips upside down on your wrist and you can't read the word.

   Tip:

   If the bracelet is a gift, ask the recipient or borrow a bracelet they already wear comfortably and copy that length.

   Mark step done

   Used in this stepTape Measure

   Back to all steps

4. 4

   Step 4: Lay out the full design on the bead board

   Watch this step · 3:15

   Enlarge

   Work the design out flat before you string anything. Put the word in the middle, then add even rows of band beads on each side until the total length matches your target.

   Creative Fnk uses two purple pearl beads and one white pearl bead in a repeating pattern. You can copy that or build your own rhythm - alternating colors, all one color, gradient from light to dark. As long as the word lands centered, the band design is yours.

   Mark step done

   Used in this step6mm Pearl BeadsFaceted Accent Beads

   Back to all steps
5. 5

   Step 5: Cut and pre-stretch the elastic

   Watch this step · 4:10

   Enlarge

   Cut about 25cm of 0.7mm Stretch Magic elastic. That's a generous length for a single bracelet, but you want plenty of slack at both ends to tie a clean knot.

   Pre-stretch the cord before you string. Hold one end in each hand and give it a firm, steady pull a few times. Stretch Magic has a slight jelly quality fresh from the spool. Tugging it now stops the bracelet from going loose a week after you finish it.

   Tip:

   If you skip the pre-stretch, the bracelet will look perfect when you tie it and feel sloppy by the second time you put it on. Always pre-stretch.

   Mark step done

   Used in this stepStretch Magic Cord 0.7mmScissors

   Back to all steps

6. 6

   Step 6: Clip one end and thread the beads

   Watch this step · 4:40

   Enlarge

   Slide a bead stopper or small binder clip onto one end of the elastic. That keeps the beads from sliding off while you string.

   Now thread in your planned order - band beads, frame seed bead, the letters, frame seed bead, band beads. Push them down as you go and check the total length against your target every few beads. Stop a bead or two short of your number so you have room to fine-tune before the knot.

   Mark step done

   Used in this stepBead StoppersAlphabet Bead Variety Pack

   Back to all steps

7. 7

   Step 7: Tie a surgeon's knot

   Watch this step · 5:20

   Enlarge

   Slide one last seed bead onto the back of the bracelet - that's the one you'll bury the knot under.

   Now tie a surgeon's knot. First half is a normal knot: left strand over right, through the middle, pull snug. Second half is the lock: right strand over left, but this time wrap it through five times instead of once. Pull the first knot tight first, then carefully snug down the five-wrap stack on top of it. Tug gently on all four cord ends to set the elastic.

   Tip:

   The five wraps are what makes this knot hold on stretch cord. A regular square knot will slip. A surgeon's knot won't.

   Mark step done

   Used in this stepStretch Magic Cord 0.7mm

   Back to all steps

8. 8

   Step 8: Trim, hide the knot, then stack and wear

   Watch this step · 10:40

   Enlarge

   Trim the elastic tails close to the knot - about 1 to 2mm. Don't shave them flush, the knot can pop loose if you cut too close. Gently twist the bracelet so the last seed bead slides over the top of the knot and hides it.

   That's one done. Now make a few more. Letter bead bracelets look best stacked - one name, one word, one lyric, one inside joke. A single MAMA on its own is sweet. Three or four on the same wrist is the look. Trade one with a friend.

   Tip:

   If the knot won't stay hidden, a tiny drop of clear nail polish or jewelry glue locks it without showing.

   Mark step done

   Used in this stepScissorsJewelry Glue

   Back to all steps

Keep going

How to Tie a Bracelet Knot (Adjustable Sliding Knot)

8 steps · about 5 minutes

→

Tools we recommend

• E6000

  E6000 Craft Adhesive, Clear (3.7 oz)

  The industrial-strength craft glue that bonds glass, wood, ceramic, metal, fabric, and concrete. The one adhesive most craft projects reach for.

• Gorilla

  Gorilla Dual-Temp Full-Size Hot Glue Gun

  Dual-temp so it handles delicate florals and heavy materials alike. A precise nozzle and built-in stand make it the everyday craft-table gun.

• OLFA

  OLFA 18" x 24" Self-Healing Cutting Mat

  The pro-standard cutting surface. Gridlines for square cuts, self-healing so blades never leave grooves, and big enough for paper, fabric, and leather.

Tags