How to Make a Mosaic Flower Pot

1. 1

   Step 1: Seal the Pot and Gather Supplies

   Watch this step · 0:44

   Enlarge

   Start with plain terracotta pots. Chrissy seals the inside and outside of each pot with a clay pot sealer first, which helps the finished piece hold up outdoors. Pull together the rest of your supplies while that dries: a plate you love, tile nippers, gloves, and safety goggles. She grabbed a blue and white plate at her local thrift store and knew right away it would make a pretty pot.

   Tip:

   No plate on hand? Pre-cut mosaic tiles from a craft store work just as well and mix in nicely with plate pieces.

   Mark step done

   Used in this stepterracotta potclay pot sealer

   Back to all steps

2. 2

   Step 2: Break the Plate with Tile Nippers

   Watch this step · 1:20

   Enlarge

   Put your safety goggles and gloves on before you break anything. Take your tile nippers and start snapping the plate into smaller pieces. Chrissy works inside a cardboard box so the shards stay contained, because it gets messy as the pieces get smaller. If you'd rather keep it fully sealed off, drop the plate in a ziploc bag and break it inside the bag.

   Tip:

   Chrissy calls this the best stress relief in the whole project. Take your time and enjoy it.

   Mark step done

   Used in this steptile nipperssafety goggles

   Back to all steps

3. 3

   Step 3: Nip the Pieces Down to Size

   Watch this step · 2:05

   Enlarge

   Keep nipping until your pieces land around half an inch to three-quarters of an inch. That size lays flat on a small pot and grouts cleanly. Chrissy mixed in a second plate she found at Goodwill for a couple of dollars, though she notes a curved salad plate is harder to cut than a flatter dinner plate. Experiment with different plates and pot sizes to see what you like.

   Mark step done

   Used in this stepmosaic glass tiles

   Back to all steps

4. 4

   Step 4: Glue the Tiles onto the Pot

   Watch this step · 3:05

   Enlarge

   Now the design comes together. Spread tile adhesive on the pot and press your pieces on in a pattern. Chrissy scales her tile sizes to the pot, so for these small pots she sticks with the half-inch to three-quarter-inch pieces. She sets square tiles around the rim as a border, then fills the body in a random pattern. If she did it again, she'd measure the rim first and space the border tiles a little closer together.

   Tip:

   Lay a few tiles out dry before gluing so you can see the pattern and count how many border pieces you need.

   Mark step done

   Used in this stepceramic tile adhesive

   Back to all steps
5. 5

   Step 5: Mix the Grout

   Watch this step · 3:20

   Enlarge

   Let the adhesive set for about five or six hours, then mix your grout. Chrissy stirs powdered grout with water until it hits a consistency like toothpaste. Her one big piece of advice: make more grout than you think you'll need. You do not want to run out halfway through a pot and have to mix a fresh batch that doesn't match.

   Mark step done

   Used in this stepsanded grout

   Back to all steps

6. 6

   Step 6: Spread Grout Over the Tiles

   Watch this step · 3:50

   Enlarge

   Work the grout over the entire pot with gloved hands, pushing it into every crack and crevice between the tiles. Do not panic when the whole thing disappears under a layer of grout. It looks like a mess at this stage and that is exactly right. The gaps have to be packed full for the mosaic to hold together and look finished.

   Tip:

   Press firmly so no air pockets hide in the gaps between pieces.

   Mark step done

   Used in this stepsanded grout

   Back to all steps

7. 7

   Step 7: Wipe It Clean to Reveal the Design

   Watch this step · 4:10

   Enlarge

   This is where it gets pretty. Take a sponge that's just barely damp and scrape the grout off the faces of the tiles. The pattern appears as you go, and the colors pop back through the haze. Rinse and wring your sponge often so you're not smearing grout back onto the tiles you already cleaned.

   Mark step done

   Used in this stepgrout sponge

   Back to all steps

8. 8

   Step 8: Cure, Seal, and Plant

   Watch this step · 5:02

   Enlarge

   Let the pot cure overnight so the grout sets before you touch it. The next day, buff it with a clean damp cloth to clear any last grout haze. Chrissy also seals the grout with a mosaic tile sealer, which isn't required but helps the pot last longer outside. Then plant your flowers and set it out on the patio. That thrift-store plate is now a planter no one else has.

   Tip:

   Sealing the grout is optional but worth it if the pot lives outdoors year round.

   Mark step done

   Used in this stepmosaic tile sealer

   Back to all steps

Keep going

How to Make a Mosaic Stepping Stone

→

Tools we recommend

• E6000

  E6000 Craft Adhesive, Clear (3.7 oz)

  The industrial-strength craft glue that bonds glass, wood, ceramic, metal, fabric, and concrete. The one adhesive most craft projects reach for.

• Gorilla

  Gorilla Dual-Temp Full-Size Hot Glue Gun

  Dual-temp so it handles delicate florals and heavy materials alike. A precise nozzle and built-in stand make it the everyday craft-table gun.

• OLFA

  OLFA 18" x 24" Self-Healing Cutting Mat

  The pro-standard cutting surface. Gridlines for square cuts, self-healing so blades never leave grooves, and big enough for paper, fabric, and leather.

Tags