How to Make a Macrame Wall Hanging - Beginner Pattern

1. 1

   Step 1: Gather Your Supplies

   Watch this step · 0:30

   Enlarge

   You need cotton macrame cord (7mm thickness is the standard for wall hangings), sharp scissors, a measuring tape, masking tape, and a 2-foot wood dowel or natural branch.

   Cotton cord gives a soft, lived-in look once it unravels at the bottom into fringe. Avoid synthetic cord - it doesn't fray the same way and the texture feels plasticky.

   Tip:

   Look for a natural-finish wooden branch instead of a perfect dowel - it adds rustic character. Most craft stores sell them in the floral or wedding section.

   Mark step done

   Used in this step7mm Cotton Macrame Cord (50ft)Wooden Macrame Dowel 24 inchSharp Fabric Scissors

   Back to all steps

2. 2

   Step 2: Cut Your Cords

   Watch this step · 1:50

   Enlarge

   Cut 8 cords at 8 feet each - these go in the center of the design and need extra length for all the knots. Then cut 18 cords at 6 feet each - these add to the sides later.

   Lay them flat on the floor as you cut so the lengths stay even. Cotton cord stretches if you measure it under tension.

   Tip:

   Always cut a foot longer than you think you need. Macrame eats cord faster than expected, and running out 3/4 of the way through the design is the worst feeling.

   Mark step done

   Back to all steps

3. 3

   Step 3: Attach Cords with Larkshead Knots

   Watch this step · 1:15

   Enlarge

   Tape the dowel to a flat surface or hang it on a hook so it stays still. Fold each 8-foot cord in half. Loop the fold over the front of the dowel, pull both tails back through the loop, and snug it up.

   That's a larkshead knot. Repeat with all 8 cords, spaced evenly across the center of the dowel.

   Tip:

   Push each new larkshead snug against the previous one - small gaps look intentional, big gaps look sloppy.

   Mark step done

   Back to all steps

4. 4

   Step 4: Tie the First Square Knot Row

   Watch this step · 2:25

   Enlarge

   Group the hanging cords into bundles of 4 (the two outer cords are the working cords, the two inner cords are the filler).

   Drop down 3.5 inches from the dowel. Tie a square knot at each bundle. A square knot is two half-knots tied in opposite directions - left over right, then right over left.

   Tip:

   Keep your tension even across all the knots in one row. Pull each knot to the same tightness or the row dips and waves.

   Mark step done

   Back to all steps
5. 5

   Step 5: Build Square Knot Rows in a V

   Watch this step · 3:20

   Enlarge

   Drop another 2.5 inches and tie the second row of square knots, but offset between the first row's knots (this is called alternating square knots).

   Repeat with another row of 2 knots offset 2.5 inches below, then a final single knot at the bottom point. The result is a downward-pointing V of square knots in the center.

   Tip:

   If your V isn't centered on the dowel, you used different bundles than expected for the offset. Untie back to the previous row and start the alternation pattern over.

   Mark step done

   Back to all steps

6. 6

   Step 6: Attach 18 More Cords

   Watch this step · 5:30

   Enlarge

   Take the 18 shorter (6-foot) cords. Attach them with larkshead knots in groups of 3 - that's 3 cords per section, alternating sections on each side of the central V.

   Once all are attached, the dowel is fully covered with cords hanging down. The design is starting to take shape now.

   Tip:

   The video calls these 'larks heads' but the technique is identical to step 3 - just three folded cords instead of one. Pinch all three folds together before threading through the loop.

   Mark step done

   Back to all steps

7. 7

   Step 7: Diagonal Double Half Hitch Knots

   Watch this step · 7:40

   Enlarge

   Starting from the leftmost cord at the top, tie diagonal double half hitch knots working down toward the center. Each knot wraps the working cord twice around a holding cord laid diagonally across the design.

   Repeat from the right side. The two diagonal lines meet at the bottom of the central V to frame the square-knot section in a diamond shape.

   Tip:

   Double half hitch is the slowest knot in macrame - don't rush. The diagonal angle has to stay consistent or the V looks crooked.

   Mark step done

   Back to all steps

8. 8

   Step 8: Trim the Bottom Fringe

   Watch this step · 12:00

   Enlarge

   Tape a piece of masking tape across the bottom in a V or straight line - this is your cut guide. Trim the cords with sharp scissors right along the tape edge.

   Pull the masking tape off and comb out the fringe with your fingers if you want a fluffier, lived-in look. Hang the dowel on a wall hook.

   Tip:

   Steam-iron the cord ends after trimming for a neat finish. A little water in a spray bottle plus an iron on the cotton setting tames frizzy ends in seconds.

   Mark step done

   Back to all steps

Keep going

Easy Macrame Wall Hanging for Beginners

→

Tools we recommend

• E6000

  E6000 Craft Adhesive, Clear (3.7 oz)

  The industrial-strength craft glue that bonds glass, wood, ceramic, metal, fabric, and concrete. The one adhesive most craft projects reach for.

• Gorilla

  Gorilla Dual-Temp Full-Size Hot Glue Gun

  Dual-temp so it handles delicate florals and heavy materials alike. A precise nozzle and built-in stand make it the everyday craft-table gun.

• OLFA

  OLFA 18" x 24" Self-Healing Cutting Mat

  The pro-standard cutting surface. Gridlines for square cuts, self-healing so blades never leave grooves, and big enough for paper, fabric, and leather.

Tags