How to Make Stepping Stones with a Pebble Mosaic

The finished result: How to Make Stepping Stones with a Pebble Mosaic
  • Difficulty: Medium
  • 8 steps

You tapped Save

Save this project for later

We'll email you a link, no password.

How to Make Stepping Stones with a Pebble Mosaic

  • Your saved projects in one list
  • Your ticked steps on any device

Check your inbox for an email from us. Not there? Look in your spam folder.

Print

Steps written out by Crafting Step by Step from Wood Glueru's video (opens YouTube) (7:11). Published .

Stepping stones are one of those projects that look so much better when you make them yourself. A store-bought paver does the job, but a pebble mosaic stone you cast in your driveway becomes the thing visitors stop to look at on the way down the path.

This build follows Wood Glueru, who knocks together a simple plywood form, pours a square slab of concrete, and presses river pebbles into the wet mix to lay out a flowing color-banded pattern. The finished stone gets dropped into a side-yard walkway alongside others to build out a full mosaic path.

The technique is forgiving. You don't need a perfect form or expensive stones - a $30 stack of cement and a bucket of pebbles from a landscape supply yard gets you a handful of one-of-a-kind stepping stones for the cost of a single store-bought paver. Work outside, give yourself a long afternoon, and have a beer waiting for the cure.

What you'll need

Free, for this project

Get this checklist by email

  • All 14 tools and materials, with tick boxes
  • A link to print all 8 steps on paper, to keep by you while you craft

No password. The whole tutorial stays free on this page.

Quick answer

Make stunning DIY stepping stones with a pebble mosaic finish. A medium project. You need 14 things, including Quick-set concrete mix, Assorted river pebbles and Chicken wire mesh. The 8 steps start with build a Simple Plywood Form, line the Form With Plastic Sheeting, mix Your Concrete and Glove Up, pour the Concrete and Press in Chicken Wire, start Placing Pebbles From the Edge, arrange the Pattern and Tap Stones Level and sponge the Pebble Tops Clean.

Step-by-step guide

8 steps, about 7 minutes. Tap a picture to jump to that step. Your progress saves automatically.

Tick each step off as you go.

  1. Step 1: Build a Simple Plywood Form

    Watch this step · 0:08

    Knock together a square form from scrap plywood and 2x4 strips. The bottom is a flat plywood panel; the sides are four short pieces screwed in from underneath. Aim for a stone roughly 16 to 18 inches square and about an inch and a half deep.

    The trick is keeping your screws accessible. When the slab cures you'll back the screws out to release the form, so don't bury the screw heads under the concrete. Drive them from the outside in.

    Tip:

    Scrap wood is fine. The form is single-use - the concrete will stain it - so don't waste your nice plywood.

    Back to all steps

  2. Step 2: Line the Form With Plastic Sheeting

    Watch this step · 1:00

    Lay a sheet of plastic across the inside of the form and press it down into the corners. This is your mold release - the concrete will not bond to plastic, so the slab pops free when you take the form apart.

    A cheap painter's drop cloth or a contractor garbage bag both work. Don't worry about wrinkles. They'll show as faint texture on the bottom of the finished stone, which nobody sees once it's in the ground.

    Tip:

    Let the plastic drape a few inches up over the side rails. That way when you pour, the cement can't sneak between the plastic and the wood.

    Back to all steps

  3. Step 3: Mix Your Concrete and Glove Up

    Watch this step · 1:18

    Dump a bag of quick-set concrete mix into a wheelbarrow and add water a little at a time. Stir with a trowel or a scrap of 2x4 until you get a thick scoopable consistency - somewhere between oatmeal and brownie batter. Too wet and the stones will sink right through; too dry and they won't seat properly.

    Pull on a pair of long rubber gloves before you touch the wet mix. Cement is alkaline and will burn skin after a few minutes of contact. The orange dishwashing gloves are perfect because they reach past your wrist.

    Tip:

    Quick-set concrete sets in about 30 to 45 minutes. Have your stones laid out and ready before you start the pour.

    Back to all steps

  4. Step 4: Pour the Concrete and Press in Chicken Wire

    Watch this step · 1:40

    Scoop the concrete into the lined form and spread it out to roughly an inch thick. Lay a square of chicken wire mesh across the top and press it down into the wet mix. The wire is reinforcement - it keeps the slab from cracking the first time someone steps on a corner.

    Once the wire is buried, scoop another half-inch layer of concrete on top so the wire ends up sandwiched in the middle of the slab. Smooth the surface flat with a gloved palm or a trowel before you start placing stones.

    Tip:

    Tin snips cut chicken wire fast. Trim the mesh about an inch smaller than the form so no sharp ends poke out the sides.

    Back to all steps

  5. Step 5: Start Placing Pebbles From the Edge

    Watch this step · 2:35

    Start at one corner and press your first pebbles into the wet concrete. Push each stone down so about half of it sinks into the mix and the top half stays exposed. Work from an edge inward so you always have a clean line to butt the next stone against.

    Sort your pebbles by color and size before you start - this is the most relaxing part of the build but it goes fast once the cement starts setting up. White and cream stones, brown and rust stones, slate-gray stones - keep them in separate piles within arm's reach.

    Tip:

    Use a chopstick or a butter knife to nudge small stones into tight gaps without disturbing the ones you already placed.

    Back to all steps

  6. Step 6: Arrange the Pattern and Tap Stones Level

    Watch this step · 4:00

    Keep filling the slab in your chosen pattern. A flowing spiral, color-banded sections, or a sun-and-moon split all read well from above. Group by color so each section feels intentional rather than random.

    Lay a flat scrap of 2x4 across the form and tap the board gently with a rubber mallet. The board distributes the pressure so the tops of all the stones settle to the same height. Slide the board across the whole slab and tap a few times in each spot until everything is level.

    Tip:

    If a stone sinks too far, pull it out with your gloved fingers, scrape a little cement into the hole, and reseat it higher.

    Back to all steps

  7. Step 7: Sponge the Pebble Tops Clean

    Watch this step · 5:20

    Wet a large sponge, wring it out, and wipe across the tops of the stones. Cement haze comes off easily while it's still fresh - wait an hour and you'll need acid to get it back. Rinse the sponge in a bucket of water between passes so you're not just smearing the haze around.

    Use a gloved fingertip to smooth the cement in the joints between stones. Aim for a slight dip below the stone tops so each pebble reads as a clean shape, not a stone half-drowned in concrete.

    Tip:

    Don't soak the slab. Excess water on top of curing cement weakens the surface and leaves a chalky finish.

    Back to all steps

  8. Step 8: Cure 24 to 48 Hours and Remove the Form

    Watch this step · 6:50

    Drape a sheet of plastic loosely over the slab and walk away. Concrete cures slowly. Give it a full 24 hours before you touch it, 48 hours before you put weight on it. Curing in the shade with a little surface moisture trapped under the plastic actually makes a stronger stone than curing in direct sun.

    When it's hard, back out your screws, lift the form sides away, and peel the plastic off the bottom. Drop the finished stone into the garden path. Optional final move: brush a coat of clear concrete sealer over the top to deepen the pebble colors and protect against frost.

    Tip:

    Two or three stones in a row look like a project. Five or more start to look like a path. Mix and pour the next one while the first is curing.

    Back to all steps

How to Build a Cedar Birdhouse

Keep going

How to Build a Cedar Birdhouse

Keep going with gardening

More on this topic, picked for this project.

You reached the last step

Save this project to come back to it

Your ticked steps, the free printable and your other saved makes, together in My Projects. Free, no password.

You tapped Save

Save this project for later

We'll email you a link, no password.

How to Make Stepping Stones with a Pebble Mosaic

  • Your saved projects in one list
  • Your ticked steps on any device

Check your inbox for an email from us. Not there? Look in your spam folder.

Products Used

The Checklist

How to Make Stepping Stones with a Pebble Mosaic

Tools
7
Materials
7
Steps
8
Video
7 min

Tools we recommend

As an Amazon Associate we earn from qualifying purchases. Links on this page may be affiliate links - clicking them and buying doesn't change your price, but helps support Crafting Step by Step.

Tags

The Crafter's Weekly

New gardening tutorials, every Sunday

One short email with the week's best step-by-step guides. Free, no spam, unsubscribe anytime.

Test your knowledge

Did the lesson stick? Start with this one.

5 questions covering what you just read. No signup, no score saved, and you can stop after this one.

Question 1 of 5

Why drive the form's screws from the outside in, not from inside the form?

Quick reference

Key takeaways from How to Make Stepping Stones with a Pebble Mosaic

5 questions, answers, and one-line explanations. Tap to expand.

  1. 1.Why drive the form's screws from the outside in, not from inside the form?

    Answer: So you can back them out to release the slab after curing

    When the slab cures, the screws have to come out. Heads buried in concrete make the form impossible to break apart.

  2. 2.What's the purpose of the plastic sheeting laid inside the form?

    Answer: To act as a mold release so the slab pops free

    Concrete won't bond to plastic, so the slab releases cleanly when you break the form apart.

  3. 3.How wet should the concrete mix be when you pour it?

    Answer: Between oatmeal and brownie batter

    Too wet, stones sink through. Too dry, they won't seat. Thick-scoopable is the sweet spot.

  4. 4.Where does the chicken wire reinforcement go in the slab?

    Answer: Sandwiched in the middle of the concrete

    Wire in the middle keeps the slab from cracking the first time someone steps on a corner.

  5. 5.How long should you cure the stone before walking on it?

    Answer: 24 hours before touching, 48 before walking on it

    Slow cures are stronger. Wait 24 hours before touching, 48 before it carries weight.

Did this work for you?

What's next

Similar tutorials

Hand-picked next reads based on the one you just finished.

Liked this gardening tutorial?

Pick the crafts you want to hear about. One email every Sunday with new step-by-step tutorials. No spam, easy to unsubscribe.

Get more like this in your inbox

Weekly digest. Pick the categories you want. Unsubscribe anytime.

Send me tutorials about

We only email about new tutorials. Easy unsubscribe anytime.