How to Make a Mosaic Suncatcher
Source: mosaicsbymaricela • Full tutorial: www.craftingstepbystep.com/crafts/how-to-make-a-mosaic-suncatcher
- Difficulty
- Medium
- Hands-on time
- About 1 hour
- Wait time
- 30 minutes
- Cost
- About $15 to $25
- Makes
- 1 mosaic glass suncatcher
Tools
- Wheel glass nippers
- Safety glasses
- Small syringe applicator
- Nitrile gloves
- Grout mixing bowl
- Grout spreader
- Sponge
- Microfiber cloth
- Sharpie marker
Materials
- Clear glass suncatcher blank with hanging hoop
- Stained glass scraps
- Ball chain
- Clear drying adhesive
- Powdered tile grout
- Painter's tape
- Paper
Steps
1. Sort Your Glass Scraps by Colour
Sort your stained glass scraps by colour. If you bought a scrap bag, give the pieces a quick wash and pat them dry before you start.
Tip: A white plate or sheet of paper underneath shows you the true colour. Glass reads very differently against a dark bench.

2. Sketch Your Design on Paper
Trace around your suncatcher base onto a sheet of paper, then sketch your design inside the circle. Wavy horizontal bands work well for a first attempt because the lines do not have to be precise.
Tip: Keep the bands wider than your smallest glass piece. Narrow sections are fiddly to fill and look cluttered.

3. Tape the Sketch Under the Base
Slide the sketch underneath the clear suncatcher base and tape it in place. Setting the whole thing on a foam block keeps it from sliding around while you work.
Tip: The original packaging the blank came in usually works as a base. It is already the right size and costs nothing.

4. Lay Out the Glass by Colour
Lay your glass out beside the base and start testing colour combinations. Move the groups around until the order looks right to you.
Tip: Photograph two or three layouts on your phone and compare them. Small differences are much easier to judge on screen.

5. Load the Adhesive Into a Syringe
Transfer some clear adhesive into a small syringe. Gorilla clear glue holds well on glass and dries clear, but squeezing it straight from the tube gives you far too much.
Tip: Keep the tube in the fridge. Clear adhesives skin over fast once opened and a cold tube lasts noticeably longer.

6. Glue Down the Ball Chain
Cut lengths of ball chain and glue them along your sketched lines. The chain gives you a clean metallic border between sections and hides the joins where two colours meet.
Tip: Cut the chain a little long and trim at the edge once it is down. Stretching a short piece to fit pulls it off the line.

7. Cut the Glass With Wheel Nippers
Put your safety glasses on and cut the glass with wheel nippers. Position the wheels where you want the break, squeeze, and the piece snaps apart.
Tip: Mark your cut line with a Sharpie first. If the cut goes wrong the ink wipes off with alcohol and you have lost nothing.

8. Fill Each Section One Colour at a Time
Fill one section at a time, keeping each band a single colour. Put a small dot of adhesive on the back of every piece and press it down firmly so the glue spreads underneath.
Tip: If your glass has a texture, lay the textured side down. It still reads through and it stops grout catching in the surface.

9. Mix and Spread the Grout
Mix about three spoonfuls of powdered grout with water until it reaches a peanut butter consistency. Let it slake for five minutes, which lets the chemical reaction strengthen it.
Tip: Add water a little at a time. Grout goes from crumbly to soup in about half a teaspoon and you cannot take it back out.

10. Wipe Back and Polish
Wipe the excess grout away with a paper towel once it has firmed up. A damp sponge gets into the tight spots around the ball chain.
Tip: Rinse the sponge often and wring it hard. A wet sponge pulls grout back out of the gaps you just filled.
