Crafting Step by Step

How to Make a Bottle Brush Tree Wreath

Source: J Dub By Design™ • Full tutorial: www.craftingstepbystep.com/crafts/how-to-make-a-bottle-brush-tree-wreath

Difficulty
Easy
Hands-on time
About 30 minutes
Cost
About $15 to $35
Makes
1 wreath

Tools

  • hot glue gun
  • wire cutters
  • scissors

Materials

  • small grapevine wreath
  • 3 bottle brush trees
  • artificial pine garland
  • mini pine cones
  • 2 sleigh bells on twine
  • raffia
  • velvet ribbon
  • gold ball picks
  • hot glue sticks

Steps

  1. 1. Gather the Grapevine Wreath, Bottle Brush Trees and Trims

    Lay everything out on the table before you start. You need a small grapevine wreath, three bottle brush trees with their bases removed and pine garland cut into short pieces.

    Tip: Grapevine wreaths from the grocery store are often cinnamon scented, which is a nice bonus.

  2. 2. Push the First Bottle Brush Tree Into the Grapevine Wreath

    Decide which part of the wreath will be the bottom. Take your tallest tree and push its wire stem straight down into the vines at the center of that section.

    Tip: Stand the wreath up now and then to check the tree looks straight when it hangs.

  3. 3. Add Two More Bottle Brush Trees on Either Side

    Place a shorter tree on each side of the first one, close enough that they look like a little grove. Push the stems in the same way.

    Tip: Cut the wire stem, not the brush, so the tree keeps its shape.

  4. 4. Tuck Pine Sprigs Behind the Bottle Brush Trees

    Cut your pine garland into pieces about 4 to 6 inches long. Take one sprig and push its pointed end into the vines behind the trees.

    Tip: Bend the wire inside each sprig to point the needles where you want them.

  5. 5. Fill Out the Wreath Sides With More Pine Greenery

    Now work outward. Add longer sprigs to the left and right of the trees so the greenery sweeps partway up each side of the wreath.

    Tip: Hold the wreath up at arm's length to spot any thin areas.

  6. 6. Glue Mini Pine Cones Into the Wreath Greenery

    Cut small pine cones off a spare pine cone garland or use loose mini cones. Put a drop of hot glue on the bottom of each one and press it into the greenery, close to the vines so the glue can grab.

    Tip: Hold each cone for a few seconds while the glue sets.

  7. 7. Thread Two Sleigh Bells Through the Grapevine Wreath

    Turn the wreath so the trees are at the bottom. Take a sleigh bell on its twine and run the twine through the grapevine at the top.

    Tip: Trim the twine so the bells hang inside the wreath, not below it.

  8. 8. Glue a Raffia Bow to the Top of the Wreath

    Make a simple bow from a bundle of raffia strands and tie it in the middle. Put a little hot glue on the back and press it onto the top of the wreath, right over where the bells hang.

    Tip: Use eight to ten raffia strands for a bow that looks full on a small wreath.

  9. 9. Layer a Velvet Ribbon Bow Over the Raffia Bow

    Tie a bow using two velvet ribbons held together, like dark green and gold. Glue it on top of the raffia bow so the two layers sit as one.

    Tip: Sharp scissors give velvet a clean dovetail without fraying.

  10. 10. Tuck Gold Ball Picks Into the Wreath Greenery

    For a final bit of shine, add small gold ball picks. Push their stems into the greenery around the trees and along the sides, the same way you placed the pine.

    Tip: Keep the gold balls in groups of three for a balanced look.

My notes

Scan for the full tutorial and video

Full tutorial with videos and details at www.craftingstepbystep.com/crafts/how-to-make-a-bottle-brush-tree-wreath