{"title":"How to Make a Popsicle Stick Sled Ornament","canonicalUrl":"https://www.craftingstepbystep.com/crafts/how-to-make-a-popsicle-stick-sled-ornament","category":{"slug":"crafts","name":"Crafts"},"creator":{"name":"Christine's Crafts","channelUrl":"https://www.youtube.com/channel/UCbRSvs3mCdAtCCy9CMLGUZA","sourceVideoUrl":"https://www.youtube.com/watch?v=aLL1x0joMho"},"tldr":"Make a popsicle stick sled ornament with craft sticks, glue and twine. A quick, low-cost Christmas craft for kids and grandkids.","quickAnswer":"Make a popsicle stick sled ornament with craft sticks, glue and twine. An easy project: about 20 minutes, plus 1 hour to dry or set. Materials cost about $1 to $3. You need 6 things, including craft sticks, jute twine and red paint. The 9 steps start with cut Three Popsicle Sticks to the Same Length for the Sled Seat and line Up the Popsicle Sticks With the Middle One Set Forward.","totalDurationSeconds":350,"videoDurationSeconds":350,"difficulty":"easy","project":{"difficulty":"easy","projectMinutes":20,"waitMinutes":60,"totalMinutes":80,"estimatedCost":{"currency":"USD","min":1,"max":3},"yield":"1 sled ornament"},"tools":["craft scissors","baking paper or a craft mat"],"materials":["craft sticks (red or plain)","clear all purpose or tacky glue","jute twine","red paint (optional, for plain sticks)"],"steps":[{"number":1,"title":"Cut Three Popsicle Sticks to the Same Length for the Sled Seat","text":"The seat is three sticks wide. If all your sticks are the same length, cut three of them a little shorter. Christine lays each cut piece on top of the next stick so she can trim it to match. Cut slowly with sturdy scissors, and watch out, because small bits of stick tend to fly off. You can make the seat wider or narrower if you like."},{"number":2,"title":"Line Up the Popsicle Sticks With the Middle One Set Forward","text":"Lay the three seat sticks next to each other. Christine sets the middle one slightly forward of the other two. It gives the seat a nicer shape that reads as a sled. Hold a full stick across the back ends to check that they are lined up. Then run a thin line of glue along the edges where the sticks touch, so they hold together."},{"number":3,"title":"Glue a Second Layer of Popsicle Stick Onto the Sled Seat","text":"Edge glue alone will not hold the seat for long. Cut a short piece of craft stick and glue it across the seat to add another layer. It holds the three sticks in place and makes the seat a lot more secure. Press it down for a moment so the glue grabs before you let go."},{"number":4,"title":"Glue a Short Brace Across the Popsicle Stick Seat","text":"Cut one more piece of craft stick so it spans all three seat sticks. Leave a small gap at each edge, because the runners will go there. Christine trims hers twice to get it right. Glue it across the seat for extra stiffness so the sled does not fall apart. Then leave the seat to dry for a few minutes."},{"number":5,"title":"Glue a Full Popsicle Stick Runner Along Each Side of the Sled","text":"Once the seat is dry, turn it over. Run a thin line of glue along each side of the bottom face. Lay a full-length stick along each side as a runner. Christine places them quite far forward on the sled, because the seat sits at the back. Doing both runners at the same time means they line up and dry together."},{"number":6,"title":"Set the Popsicle Stick Runners Upright and Let Them Dry","text":"Check the runners from above. They should run straight, side by side, and stick out past the front of the seat. Stand them upright so they are not leaning in or out. Turn the sled over to see how it looks from the top. When you are happy with them, leave the runners to dry for a few minutes before you go on."},{"number":7,"title":"Glue the Front Bar Across the Popsicle Stick Sled Runners","text":"With the sled upside down, cut a stick for the front bar. Christine makes hers a little wider than the runners. Put a small dab of glue on the top of each runner tip. Lay the bar across so it sticks out the same distance on both sides. That is the whole sled. Let it dry before adding the hanger."},{"number":8,"title":"Glue the Twine Hanger Under the Sled Front Bar","text":"Turn the sled upside down again. Squeeze some glue into the corners under the front bar. Christine uses garden twine for a rustic look. Push one end of the twine into the glue on each side so it forms a loop. Some glue will squeeze out. It dries clear and it is on the underside, so nobody sees it. Leave it until it is thoroughly dry."},{"number":9,"title":"Turn Over the Finished Popsicle Stick Sled Ornament","text":"When the glue has set, turn the sled the right way up. That is your finished ornament. Decorate it however you like. Add glitter, write a name on the seat, or glue on a small photo if it is a gift for grandma. Hang it on your tree, tie it to a present, or make a few to give to friends and family."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-16T15:09:03.291Z","published":"2026-11-16T15:09:03.026Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}