{"title":"How to Make a Paper Speedboat That Floats","canonicalUrl":"https://www.craftingstepbystep.com/paper-crafts/how-to-make-a-paper-speedboat","category":{"slug":"paper-crafts","name":"Paper Crafts"},"creator":{"name":"Easy Origami and Crafts","channelUrl":"https://www.youtube.com/channel/UC5YtPtkKYR7oC3sxd_H1tPA","sourceVideoUrl":"https://www.youtube.com/watch?v=D7Kvg693cYc"},"tldr":"Fold a paper speedboat from one A4 sheet with no glue or scissors. Clear origami steps for a boat with a cockpit that really floats.","quickAnswer":"Fold a paper speedboat from one A4 sheet with no glue or scissors. A medium project: about 20 minutes. You need 3 things, including 1 sheet of A4 paper, white candle or crayon and bone folder. The 10 steps start with fold the Paper Diagonally to Start the Speedboat X Crease, fold the Paper in Half to Crease the Speedboat Center Line, collapse the Top of the Paper Into a Triangle and fold the Lower Paper Rectangle in Half Under the Triangle.","totalDurationSeconds":791,"videoDurationSeconds":791,"difficulty":"medium","project":{"difficulty":"medium","projectMinutes":20,"waitMinutes":null,"totalMinutes":20,"estimatedCost":null,"yield":"1 paper speedboat"},"tools":["bone folder (optional)"],"materials":["1 sheet of A4 paper (or any sheet with the same proportions)","white candle or crayon (optional, to waterproof)"],"steps":[{"number":1,"title":"Fold the Paper Diagonally to Start the Speedboat X Crease","text":"Turn an A4 sheet so it stands tall in front of you. To fold an X at the top, bring the top edge across to the left side, crease it and unfold. Then bring the same top edge across to the right side and crease again. The two diagonals cross near the top of the sheet and make the X that the whole boat is built on."},{"number":2,"title":"Fold the Paper in Half to Crease the Speedboat Center Line","text":"Turn the paper over. Fold the X in half horizontally so the crease runs through its center, then unfold. Next fold the whole sheet in half the long way by bringing the right side over to the left. Crease it well and unfold. Flip the paper over again, ready for the collapse."},{"number":3,"title":"Collapse the Top of the Paper Into a Triangle","text":"Press the center of the X so it pops down. Bring the two sides in toward the middle along the creases you made. The top of the sheet folds down and flattens into a triangle with the rest of the paper below it. Lower and flatten the top layer so everything sits neat and flat."},{"number":4,"title":"Fold the Lower Paper Rectangle in Half Under the Triangle","text":"Below the triangle there is still a rectangle of paper. Fold it in half by bringing the bottom edge up to the base of the triangle. Crease it firmly along the full width, pressing out from the middle. Then flip the whole piece over so the other side faces up for the next folds."},{"number":5,"title":"Fold the Sides of the Speedboat Base to the Center","text":"On this side you need two diagonal creases. Bring the right side in to the center line and make a firm crease. Then do the same with the left side. The model now looks like an arrow with a point at the top. These folds become the sloping sides of the hull."},{"number":6,"title":"Crease Small Diagonals on the Speedboat Bottom Flaps","text":"Fold the paper along the two small diagonal lines at the bottom. Fold the right flap, crease and unfold. Fold the left flap, crease and unfold. These creases are guides for later, so the paper should lie flat again when you finish this step. You will see two short creases near the bottom point, one on each side."},{"number":7,"title":"Fold the Speedboat Corners on the Guide Marks","text":"Fold the two remaining corners to make a guideline. Line each fold up with the layer underneath, not with a measurement. That matters if your paper is not exactly A4. Unfold both and open the middle. Fold the corners in on the marks you made, close both sides, then fold the two last flaps, unfold them and turn the model over."},{"number":8,"title":"Tuck the Top Layer Behind to Form the Speedboat Bow","text":"A triangle now sits in the middle. Fold it in half by bringing the top corner down to the edge, creasing only the middle layers. Then hold the paper as shown and use that crease to swing the top layer behind the middle part. Line the diagonal edge up with the point, flatten a little, and repeat on the other side."},{"number":9,"title":"Bring the Back Section Behind the Inner Layer","text":"Fold the remaining paper at the bottom, aligning with the layers below and using the two corners as a reference. Unfold. Separate the inner layer and hold it closed with your left hand. With your right hand, bring the back part behind that layer, align everything and press. Rotate the paper and repeat on the other side."},{"number":10,"title":"Open and Square Up the Paper Speedboat Hull","text":"Adjust the front of the boat first. Then open the middle layer to form the cockpit. Shape the back so it is rectangular, and square off the bottom so the boat sits flat. For a tidier finish, unfold the loose flap at each side and slip it between the inner layers. Give it a final adjustment and your speedboat is ready to float."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-17T15:44:35.410Z","published":"2026-11-17T15:44:35.193Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}