{"title":"How to Make a Fabric Gnome (Free Sewing Pattern)","canonicalUrl":"https://www.craftingstepbystep.com/crafts/how-to-make-a-fabric-gnome","category":{"slug":"crafts","name":"Crafts"},"creator":{"name":"LearnCreateSew (LearnCreateSew)","channelUrl":"https://www.youtube.com/channel/UCq8I4YlPQZg3Ha9pyjnu4Ng","sourceVideoUrl":"https://www.youtube.com/watch?v=PzG6vYNlYyg"},"tldr":"Sew a fabric gnome with a felt body, fur beard, flannel hat and bead nose. Free pattern, tips on beard fur and weighting it to stand.","quickAnswer":"Sew a fabric gnome with a felt body, fur beard, flannel hat and bead nose. An easy project: about 1 hour 30 minutes. Materials cost about $6 to $12. You need 17 things, including long pile faux fur, poly pellets and polyfil stuffing. The 10 steps start with trace the Gnome Hat Pattern Onto the Fabric, snip the Faux Fur Beard Backing With Small Scissors and pin the Fur Beard to the Red Felt Gnome Body.","totalDurationSeconds":1194,"videoDurationSeconds":1194,"difficulty":"easy","project":{"difficulty":"easy","projectMinutes":90,"waitMinutes":null,"totalMinutes":90,"estimatedCost":{"currency":"USD","min":6,"max":12},"yield":"1 gnome"},"tools":["sewing machine","fabric scissors","small embroidery scissors","pinking shears","fabric marking pen","sewing pins","hand sewing needle","funnel"],"materials":["craft felt for the body and base","flannel or cotton fat quarter for the hat","long pile faux fur","poly pellets","polyfil stuffing","wooden bead for the nose","pom pom","coordinating thread","scrap fabric for the pellet pouch"],"steps":[{"number":1,"title":"Trace the Gnome Hat Pattern Onto the Fabric","text":"Print the free LearnCreateSew pattern and tape the pieces together. The video makes the medium size here. Fold your hat fabric so you are working with one layer, lay the hat pattern on the wrong side and trace around it with a marking pen. You only need one hat piece. Cut it out, then trace and cut the body and the round base from felt the same way."},{"number":2,"title":"Snip the Faux Fur Beard Backing With Small Scissors","text":"Check which way the fur brushes down and match it to the arrow on the beard pattern. Flip the fur over, trace the beard on the back and cut it out slowly. Use small scissors and do not open them all the way. Take tiny snips through the backing only. Big cuts slice off the long hairs and give your gnome an unfortunate haircut."},{"number":3,"title":"Pin the Fur Beard to the Red Felt Gnome Body","text":"Trim the body pattern along the dotted beard placement line. Lay that top piece on the felt body to show where the beard goes. Line the top edge of the beard up with the pattern edge and center it. Pin it in place, then sew along the top edge of the beard with an eighth inch seam. Brush the fur away from the needle as you go."},{"number":4,"title":"Sew the Side Seam of the Gnome Body","text":"Fold the body in half with right sides together so the beard is hidden inside. Pin the long side. Sew from the tip down to the corner with a quarter inch seam, but leave a gap of about two and a half to three inches above the beard line for turning. Do not leave the gap at the very tip. A pointed tip is hard to slip stitch shut."},{"number":5,"title":"Sew In the Gnome Base and Clip the Curves","text":"Tuck the beard down inside, out of the way. Pin the felt circle to the bottom edge, right sides together, and sew around it with a quarter inch seam. Keep the circle flat on the machine so you can move the body fabric aside. Clip around the base with pinking shears so it lies flat, staying clear of the stitches. Trim the tip, then turn the gnome right side out."},{"number":6,"title":"Weight the Gnome Body With Poly Pellets","text":"Pour poly pellets into the bottom so your gnome stands without wobbling. A large funnel helps; small ones jam. The video goes one step further and sews two scrap fabric circles a little bigger than the base into a pouch, fills it with about 8 tablespoons of pellets, sews it shut and slides the pouch into the gnome. Flatten it on the bottom so the gnome sits level."},{"number":7,"title":"Stuff the Gnome and Slip Stitch the Opening Closed","text":"Tear polyfil into small, fluffy pieces so the body does not turn lumpy. Pack it in around the pellet pouch and shape the gnome as you go. Once the base is full, start slip stitching the opening a quarter inch from the edge. Stop halfway, add more stuffing to firm up the top, then finish the seam and knot it off."},{"number":8,"title":"Hem the Gnome Hat and Fold It Into a Cone","text":"Lay the hat right side down. Fold the curved edge up a quarter inch and stitch it down to hem it, all the way around. Press it if you like. Fold the hat in half with right sides together, sew the long side with a quarter inch seam and turn it right side out. Slip it on the gnome to check the fit. A little loose gives you slouchy folds."},{"number":9,"title":"Sew the Wooden Bead Nose on the Gnome","text":"Take the hat off. Find the back seam and go straight across to the front; that is the center of the beard. The video sets the top of the nose about a quarter inch below the top of the beard, so the hat can slouch over it. Start the needle where the knot will hide under the hat and stitch through the wooden bead several times. Wood beads can be rough inside, so pull gently."},{"number":10,"title":"Slouch the Hat Over the Gnome's Nose","text":"Sew a pom pom to the tip of the hat, stitching through the pom pom itself and not only its fluff, or hot glue it. Put the hat on with the seam at the back. Pull it down past the nose, then scrunch it up and over so it rests on the bead. Play with the folds until you like the look. A few hand stitches or dots of glue hold it in place."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-19T15:19:10.885Z","published":"2026-11-19T15:19:10.509Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}