{"title":"How to Embroider a Snowflake (Felt Ornament for Beginners)","canonicalUrl":"https://www.craftingstepbystep.com/embroidery/how-to-embroider-a-snowflake","category":{"slug":"embroidery","name":"Embroidery"},"creator":{"name":"Valeri Lewman","channelUrl":"https://www.youtube.com/channel/UCsPSkwJRnUtRm-MNsCWqveg","sourceVideoUrl":"https://www.youtube.com/watch?v=jJ7eZXbwDhU"},"tldr":"Stitch a red snowflake on felt with a stick and stitch pattern and back stitch, then turn it into a stuffed Christmas ornament. Beginner friendly.","quickAnswer":"Stitch a red snowflake on felt with a stick and stitch pattern and back stitch, then turn it into a stuffed Christmas ornament. An easy project: about 1 hour 15 minutes, plus 1 hour to dry or set. Materials cost about $3 to $8. You need 10 things, including felt sheets, stick and stitch snowflake pattern and red embroidery floss. The 10 steps start with trace the Ornament Template Onto Felt and stick the Snowflake Embroidery Pattern on the Felt.","totalDurationSeconds":952,"videoDurationSeconds":952,"difficulty":"easy","project":{"difficulty":"easy","projectMinutes":75,"waitMinutes":60,"totalMinutes":135,"estimatedCost":{"currency":"USD","min":3,"max":8},"yield":"1 felt ornament"},"tools":["3-inch embroidery hoop","size 24 chenille needle","scissors","heat erasable pen","chopstick for stuffing"],"materials":["felt sheets","stick and stitch snowflake pattern","red embroidery floss","cotton cord","fiber fill"],"steps":[{"number":1,"title":"Trace the Ornament Template Onto Felt","text":"Print a simple ornament template and cut out the shape you want. Valeri picks a bird, but a circle, heart or mitten works too. Lay the template on your felt and trace around it with a heat erasable pen. Leave plenty of felt around the outline, because you will cut it out after the snowflake is stitched, not before."},{"number":2,"title":"Stick the Snowflake Embroidery Pattern on the Felt","text":"Choose a snowflake from your stick and stitch sheet and cut around it. Peel off the backing and press the sticky pattern onto the felt, centered inside your traced outline. Smooth it flat with your fingers so there are no bubbles. This sticker is your stitching guide, and it washes away once you are done."},{"number":3,"title":"Put the Felt Snowflake Pattern in an Embroidery Hoop","text":"Open a small embroidery hoop, about 3 inches, and lay the felt over the inner ring with the snowflake centered. Press the outer ring on and tighten the screw. Thick felt can be stitched without a hoop, but a hoop keeps the felt flat and your stitches even. It also gives you something steady to hold."},{"number":4,"title":"Practice the Colonial Knot for the Snowflake Tips","text":"Thread four strands of red floss. Come up where you want a knot. Make a backward C with the thread, bring the needle up through the C, wrap it and go down right next to the hole. Hold the working thread taut as you pull through. A French knot works the same way: wrap twice and go down beside the hole."},{"number":5,"title":"Back Stitch the Snowflake Arms in Red Floss","text":"Work along each arm of the snowflake with back stitch. Come up a stitch length ahead, go back down into the end of the last stitch, and repeat. Short sections can be a single straight stitch. Stop each arm a little short of the center to leave room for a decorative knot there. Add knots at the tips if your pattern has them."},{"number":6,"title":"Cut Out the Felt and Dissolve the Snowflake Pattern Paper","text":"Take the felt out of the hoop and cut out your ornament shape on the traced line. Then soak it in warm water, or hold it under the tap. The stick and stitch paper melts away and leaves only your red stitches. Rub gently to lift any last bits. Lay it flat to air dry, or set it near a heater vent."},{"number":7,"title":"Cut a Plain Felt Backing for the Snowflake Ornament","text":"While the front dries, trace the same template onto a second piece of felt and cut it out. This plain shape is the back of your ornament. Line the two pieces up to check they match. Trim any edge that sticks out so the two layers sit even all the way around."},{"number":8,"title":"Blanket Stitch the Two Felt Ornament Layers Together","text":"Separate two strands of floss, fold them in half and thread the folded end so you have a loop at the tail. Start at the bottom. Go through both layers from the back, catch the loop and pull to lock it. Then go through both layers a stitch length along, wrap the thread under the needle and pull snug. Repeat around the edge."},{"number":9,"title":"Stitch a Cord Hanger Into the Felt Ornament Edge","text":"Cut about 13 inches of cotton cord and knot the ends together. Slip the knot between the two felt layers at the top. Make a blanket stitch right up against one side of the cord, then one stitch between the strands, and one on the other side. Go around the cord, not through it, so it stays firm."},{"number":10,"title":"Stuff the Felt Snowflake Ornament and Finish the Edge","text":"Stop stitching with a gap of an inch or two. Push small bits of fiber fill into the ornament, starting with the narrow parts like the tail. A chopstick helps. Stuff it softly so it stays flat enough to hang. Then finish the blanket stitch, knot it on the back and tuck the tail between the layers."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-21T15:14:29.450Z","published":"2026-11-21T15:14:29.084Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}