{"title":"How to Embroider a Christmas Tree (Easy Hoop Ornament)","canonicalUrl":"https://www.craftingstepbystep.com/embroidery/how-to-embroider-a-christmas-tree","category":{"slug":"embroidery","name":"Embroidery"},"creator":{"name":"River Birch Threads","channelUrl":"https://www.youtube.com/channel/UC3j0zgnLlpV_mbQzzdt1xcw","sourceVideoUrl":"https://www.youtube.com/watch?v=Qfm8D1P40FM"},"tldr":"Embroider a Christmas tree ornament in a small hoop: backstitch branches, gold lights, French knot bulbs and a felt back. Beginner friendly.","quickAnswer":"Embroider a Christmas tree ornament in a small hoop: backstitch branches, gold lights, French knot bulbs and a felt back. An easy project: about 2 hours, plus 1 hour to dry or set. Materials cost about $5 to $12. You need 16 things, including cotton fabric, brown floss and green floss. The 10 steps start with hoop the Fabric for the Christmas Tree Embroidery, press the Christmas Tree Pattern Onto the Hooped Fabric and backstitch the Christmas Tree Trunk in Brown Floss.","totalDurationSeconds":555,"videoDurationSeconds":555,"difficulty":"easy","project":{"difficulty":"easy","projectMinutes":120,"waitMinutes":60,"totalMinutes":180,"estimatedCost":{"currency":"USD","min":5,"max":12},"yield":"1 ornament"},"tools":["3 inch embroidery hoop","embroidery needle","embroidery scissors","small paint brush","hot glue gun","embroidery stand (optional)"],"materials":["cotton fabric","stick and stitch pattern or washable marker","brown floss","green floss","gold metallic floss","colored floss for lights","white floss","brown acrylic paint","felt for the backing","ribbon for hanging"],"steps":[{"number":1,"title":"Hoop the Fabric for the Christmas Tree Embroidery","text":"Unscrew a 3 inch wooden hoop and take out the smaller inner ring. Lay a small square of fabric over it, then push the outer ring down on top and tighten the screw. Work around the edge, pulling the fabric a little at a time until it is smooth and taut. You will know it is tight enough when it sounds like a drum when you tap it."},{"number":2,"title":"Press the Christmas Tree Pattern Onto the Hooped Fabric","text":"Add the tree design. The creator uses a stick and stitch pattern: peel the mesh backing off the top and press the sticker down onto the fabric. Rub it firmly so it fuses to the weave and does not lift as you stitch. If you would rather draw your own, sketch a center trunk, slanted branches and a small star with a washable fabric marker."},{"number":3,"title":"Backstitch the Christmas Tree Trunk in Brown Floss","text":"Thread two strands of brown floss. Come up through the fabric and make a stitch about 1 cm long. Jump 1 cm ahead, come up, and go back down into the end of the last stitch. Repeat down the whole trunk. At the wide base, fill the shape with long satin stitches laid side by side. Tie a double knot on the back and trim the tail."},{"number":4,"title":"Backstitch the Green Christmas Tree Branches","text":"Switch to green floss and use three strands so the branches look full. Work the same backstitch you used on the trunk, following each branch line on the pattern from the trunk outward. Keep your stitches short on the small side branches so the curves stay smooth. Fill every branch, top to bottom, before you move on to the lights."},{"number":5,"title":"Stitch Gold Light Strings Across the Christmas Tree","text":"Give the tree sparkle with DMC Light Effects metallic floss, two strands at a time. Backstitch swags of light string across the branches the same way you did the trunk. Metallic floss sits up off the fabric more than cotton and can be fussy to pull through. Go slowly and keep at it. The shine is worth the effort."},{"number":6,"title":"Make French Knot Lights on the Christmas Tree","text":"Add the bulbs with French knots in bright colors. Come up through the fabric on a light string. Hold the floss taut with your other hand, wrap it twice around the needle and go back down in a hole right beside where you came up. Pull until the knot is snug but not tight. Pull too hard and the knot slips through to the back."},{"number":7,"title":"Stitch the Gold Star on Top of the Christmas Tree","text":"Turn the hoop so you have room at the top. Using one strand of the gold metallic floss, stitch from point to point across the star in no set order until it looks full and bright. Then thread six strands of white and add small patches of snow along a few branches. Random spots look more like fresh snowfall than an even pattern."},{"number":8,"title":"Paint the Embroidery Hoop Walnut Brown","text":"Take the embroidery out of the hoop and paint the outer ring with brown acrylic paint for a walnut look. Wood stain works too if you have it, but paint is the cheaper choice. While the hoop dries, rinse the stabilizer out of the fabric in water; it dissolves away. Let the fabric dry flat, then put it back in the painted hoop and tighten it."},{"number":9,"title":"Trim the Extra Fabric Around the Embroidery Hoop","text":"Once you are happy with how the tree sits in the hoop and the fabric is tight, turn it over. Cut away the extra fabric right down to the edge of the hoop with sharp scissors. Go slowly around the curve and keep the blades flat against the hoop so you do not snip into the embroidery or any knots on the back."},{"number":10,"title":"Glue Felt to the Back of the Embroidery Hoop Ornament","text":"Trace the hoop on felt and cut out a circle the same size. Run hot glue around the edge of the felt and press it onto the back of the hoop. The felt hides the back of your stitches and gives the ornament a neat finish. Trim away any stray glue strings, thread a ribbon through the hoop screw and hang it on your tree."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-19T15:29:45.475Z","published":"2026-11-19T15:29:45.022Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}